Paver sealing for Arlington homes
Paver Sealing in Arlington, FL
Pavers beside an Arlington ranch home can look fresh again, so call (904) 875-8988 for a free sealing estimate.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Fast, careful paver sealing in Arlington
Paver sealing is available across Arlington, and a free estimate comes first. A local contractor washes, re-sands and seals driveways, walkways and pool decks, whether your home is near the river or out toward Atlantic Boulevard. After you ask for a free estimate, you can count on a reply within 1 business day, and often much sooner.
Picture a ranch-house driveway gone dull and patchy, with sand missing from the joints, weeds poking through and a faded stripe where the sun hits longest. Once they are washed, re-sanded and sealed, those same pavers can look even and clean again. For a quick answer about your own driveway, call (904) 875-8988. Arlington is large, so it helps to say which part of it you are in.
Why hire a local paver sealing contractor in Arlington?
Arlington grew quickly for two decades after the Mathews Bridge opened in 1953, so many of its pavers have had several owners and several coats. To talk through yours, ask for a free estimate.
A no-charge first look
The contractor measures your Arlington pavers and quotes a price at no charge. If the number does not suit you, you simply say no.
A yardstick for bids
Published regional prices run $1.75 to $3.25 a square foot for the whole clean, sand and seal job, so a bid far outside that span deserves a question.
A sheen to match the house
Matte sits quietly beside brick and mid-century lines, the style Arlington is known for. A wet look shows scuffs sooner, so weigh it against the tires on your drive.
A short wait for answers
Questions about your Arlington driveway get a reply within 1 business day, usually much sooner.
Get Your Free Estimate in Arlington
Tell us about your pavers in Arlington.
Free, no obligation
What paver problems show up most in Arlington?
Sand that never stays in the joints
Arlington's ground has a sandy past. Regency Square Mall opened in 1967 on an expanse of sand dunes, and the Jacksonville Arboretum sits on land strip-mined until 1961 that left barren white sand. In USDA terms, the Ortega series first mapped in Duval County is deep, moderately well drained sand. Sand like that drains fast, which means joint sand can leave with the first hard summer storm. Open joints then let in soil and seeds, and a weed or two turns into a row of them along the edges. A MetroJacksonville history says some Arlington land sits high, with the kind of drainage early residents prized, and that same fast drainage can take joint sand along with the water.
A driveway with decades of owners
WJCT reports that many Arlington houses built in the 1950s and 1960s are still standing, and the Mathews Bridge opened in 1953. A paver driveway beside a home that old may have changed hands several times, and each owner may have picked a different sealer. Arlingwood homes date from 1953, so some pavers there have seen many seasons and many hands. Local architects Robert C. Broward, Taylor Hardwick and William Morgan designed several of the area's mid-century homes, which is part of why owners care how the pavers look beside them. A water-based sealer cannot be used over a solvent-based one, so the contractor identifies the product first. Flaking at the edges or a patchy sheen can mean something older is underneath.
Fade on wide, open drives
The Jaxson calls Arlington the city's first major post-war suburb built for the automobile, and H. Terry Parker began buying land there around 1943. Many drives here are wide and open to the sky. In July, Jacksonville's daily high averages about 92 degrees. A broad, sunny driveway tends to lose color first, and the part nearest the street often fades most. Sealer can bring the depth back, but only after the surface has been washed clean, and fresh sealer deepens the color of brick-red and tan pavers alike. Pavers that have faded evenly are easier to match than ones with a shaded strip beside a sunny strip. Choosing a finish after the wash, when the true color shows, avoids surprises.
Damp yards near creeks and ponds
Pottsburg, Strawberry and Silversmith creeks run through parts of Arlington and Woodland Acres. Wikipedia says Pottsburg Creek is fed by rain, retention ponds and storm drains, so its level swings a lot. Yards near water tend to stay damp, and green algae grows where moisture lingers. The green starts on the shaded north side of the house, and a slick film on a front walk is a slip risk. Tree Hill Nature Center, where three creeks run the length of the park, shows how much water moves through this part of town.
Brick beside the pavers, rust in the spray
Arlingwood is mostly brick ranch homes, and River Forest is mostly 1950s and 1960s ranches. Where pavers meet brick, rinse water and cleaners need care. Sprinklers matter too, since iron in well water can stain pavers orange, as University of Florida extension notes. Stains are treated first because sealer would keep them. Brick-lined walks and courtyards are common in Arlingwood, so mention yours. Aiming the spray heads away from the pavers helps keep new marks from forming.
Does paver sealing change between Arlingwood, River Forest and Woodland Acres?
The job is the same, but the story of each home changes the questions. Arlingwood is mostly brick ranch homes with a median build year of 1961, while River Forest is mostly ranch-style homes of about 800 to 1,600 square feet built in the 1950s and 1960s. Name the one you live in when you ask for a free estimate.
Lake Lucina homes were built from 1951 to 1962, with a median of 1955, and Cesery Park there honors developer William R. Cesery, who bought forty acres around 1950. Woodland Acres sits east of Southside Boulevard along three creeks and has seen infill housing, and its Warrington Park, completed in 1958, shows how many of these streets date from the same postwar years. Older and newer homes on one street can carry different pavers, so call (904) 875-8988 and describe yours.
Arlington takes in the land east and south of the river, west of the Intracoastal Waterway and north of the Arlington River. That is a lot of ground, so a cross street or a landmark helps the contractor place you, and it speeds the first reply. Name yours when you ask for a free estimate, and expect a reply within 1 business day.
What does paver sealing cost in Arlington?
The usual published price is $1.75 to $3.25 per square foot, covering the wash, the new joint sand and the sealer. A ranch lot in Arlington usually has the drive as the big piece, with a front walk and a patio added. To turn that range into a number for your lot, call (904) 875-8988.
Joint sand, old coats and algae decide where you land in that range. A driveway with a coat in good shape tends to be quicker to redo than one where the coat has failed. Put the area and the sealer name in writing when you ask for a free estimate.
| Paved area | Typical example | Clean, sand and seal |
|---|---|---|
| 300 sq ft | Small patio or walkway | $525 to $975 |
| 600 sq ft | Two car driveway | $1,050 to $1,950 |
| 1,000 sq ft | Large driveway or pool deck | $1,750 to $3,250 |
| 1,500 sq ft | Driveway plus pool deck | $2,625 to $4,875 |
Math based on the $1.75 to $3.25 per square foot that Northeast Florida paver companies publish. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.
How does a paver sealing job work in Arlington?
Check the ground and the old coat
The contractor starts on foot, with a measuring wheel and an eye for water. Dips, lifted edges and shifted pavers get marked, because sealer would lock a dip in place. Sandy ground under older Arlington drives can settle over the years, so the edges and the apron by the street get extra attention. Anything you know about earlier sealing helps, even a rough guess at the year and the brand, and so does a note about which side of the house floods first. WJCT notes the sharp edges and sloping roofs of 1950s and 1960s Arlington homes, and a clean paver edge suits that crisp look. The contractor also checks how water leaves the driveway, since pooling near the garage or the street is easy to miss.
Clean everything
Next comes the wash, and it is the step that shows what condition the pavers are in, from the first row near the garage to the last at the curb. It lifts road dirt, algae from the shaded edges and the dull film common on open ranch drives. Sprinkler rust spots are treated at this stage as well. Where pavers meet brick, cleaners and spray are kept away from the wall. Plants and flower beds along the edge are rinsed before and after, and furniture is moved out of the way.
Fill the joints
A wash carries sand away, and Arlington's sandy ground does not hold on to what is left. So fresh sand goes in, and a sweep clears the surface. Tight joints keep weeds out and help each paver stay put, which also keeps the lines straight along a long Arlington drive. If joints have been thin for years, this step gets more time. A full joint also gives the sealer a flatter surface to cover, which helps the finish look even from the street.
Give it time to dry
Pavers must be dry before any sealer is applied. A shaded side yard or a spot near a creek can lag behind a sunny driveway. The contractor reads the forecast and waits. Sealing over damp pavers shows later as cloudy or patchy spots. On a wet week, a day or two of patience beats a coat that has to be redone.
Seal, then stay off
Sealer goes on in your finish, sprayed and back-rolled, which one Jacksonville company calls typical. People can usually walk on it within a few hours, and cars stay off for about a day. The coat then runs two to five years, going by company quotes. Ask when heavy planters can go back, and keep sprinklers off the surface until the contractor says the coat has set.
Complete paver services in Arlington
Four jobs make one sealing visit: wash, new sand, dry time, sealer. The wash takes off dirt, algae and the dull film, new sand tightens the joints, and sealer closes the job once the surface is dry. To see how long each piece takes on your lot, call (904) 875-8988.
Big ranch driveways soak up the most sun and tire wear, so they fade first. Front walks by brick want gentle rinsing, and entry steps get a close look for loose pavers, since a step is where a wobble matters most. A patio or pool deck out back gets its own finish talk, since sunscreen and bare feet change the wear. Mention every surface when you ask for a free estimate.
Whatever coat is on your pavers now decides what can follow, since a solvent-based coat cannot take water-based sealer. After that, pick a look: matte fits a mid-century house, and a wet look shows scuffs sooner. Companies quote two to five years per coat. Call (904) 875-8988 to choose.
Rain mostly falls May to September, so the dry months suit a sealing job best. A shaded side yard may stay wet after the driveway dries, and sealer needs dry pavers. Cars stay off about a day, says one Jacksonville company. For a date that works, ask for a free estimate.
Questions to ask before you hire
- Which sealer do you plan to use on my pavers, and is it a film-forming or a penetrating type?
- Will the sealer leave a wet look, or a natural matte finish?
- What do I do about pavers that have sunk or shifted near my pool?
- What do you do about the rust stains from my irrigation water?
- Will you wash the pavers with a surface cleaner, or only with a hand wand?
- Will the sealer make my pool deck slippery when it is wet?
- What happens to the weeds and moss that grow in my joints before the sealer goes on?
What do sealed pavers look like around Arlington?
Why local matters in Arlington
Arlington is a mix of eras. Brick ranches from the 1950s sit near newer houses, and the pavers beside them rarely share a history or a sealer. A local contractor looks at each one fresh, and that look is free. To speak with someone who works Arlington streets, call (904) 875-8988.
Sandy ground is part of local work here. Dune sand under Regency Square and white sand at the Arboretum say the same thing about this side of the river. So joints get refilled, and slopes get a check for washout. ask for a free estimate and ask how a contractor would handle your edges.
Size matters too. Arlington runs from the river toward the Intracoastal Waterway, so a contractor plans routes and a rain backup around it. Summer storms arrive fast, and sealing waits on dry pavers. Call (904) 875-8988 and ask what timing fits your street.
How did Arlington grow, and what landmarks mark it?
Arlington grew fast after the Mathews Bridge opened in 1953, and more than 50,000 new residents had arrived by 1961. Jacksonville University, which bought land here in 1947 and finished its first building in 1950, now has a 260-acre campus. Regency Square Mall opened in 1967 on sand dunes. If you live near any of them, ask for a free estimate.
Tree Hill Nature Center, a city park since 1971, has a 300-year-old oak and a hill described as Duval County's second-highest point. Arlington Lions Club Park sits along the river, and the Dames Point Bridge, finished in 1989, links Arlington to the Northside. The Mathews Bridge and Atlantic Boulevard are good reference points as well. Pick the landmark nearest you and mention it when you call (904) 875-8988.
Frequently Asked Questions
How much does it cost to seal pavers per square foot in Arlington?
Regional prices published for this work are $1.75 to $3.25 for each square foot. In Arlington, lost joint sand and an old coat can nudge a job toward the top of that span. Ask the quote to show the total area.
Is sealing pavers a good idea in Florida, and in Arlington?
Often it is, provided you will renew the coat. Sealed pavers should bead water, which one Jacksonville company uses as its quick test. A wet look shows scuffs sooner than matte, so choose with your driveway in mind.
How long do paver sealers last in Arlington?
Two to five years is the span quoted by companies in the region. A sunny ranch drive and a shaded walk age at different speeds. A Jacksonville company says a paver that soaks up water and darkens needs a new coat.
Why is paver sealing so expensive in Arlington?
It is three jobs, not one: washing, refilling joints and sealing, plus waiting for the surface to dry. Price scales with square footage, so a wide drive adds up. Published rates sit at $1.75 to $3.25 per square foot.
How much does it take to clean and seal pavers on an Arlington ranch lot?
Your total follows the square feet of driveway, walk and patio, priced at the same published span. A lot with only a driveway costs less than one with a patio and pool deck. Have each area listed with its size.
Does an Arlington HOA have a say in paver sealing?
Possibly, though the River Forest and Arlingwood pages checked list no mandatory association. Florida Statute 720.3035 limits review to what an association's declaration or published guidelines state or reasonably imply. If you have one, read your documents first.
What about sunken pavers on my Arlington driveway?
Reset them before sealing, because a coat over a low spot only keeps the low spot. Sandy ground can settle near edges, so show the contractor each dip at the first visit.
Nearby areas we serve
Ready for a Free Estimate in Arlington?
Call (904) 875-8988 and tell us about your pavers.
Free, no obligation